Haven Hardwood’s How to Sand and Refinish Your Floor Guide

Haven Hardwood’s

How to Sand and Refinish Your Floor

Guide

Steps

•1.)                                                                Safety.

•2.)                                                                Determine if you have hardwood flooring.

•3.)                                                                Remove any layers of carpet or sub-floor.

•4.)                                                                Rent the equipment.

•5.)                                                                Sanding with the floor belt sander.

•6.)                                                                Sanding with the edger sander.

•7.)                                                                Scraping.

•8.)                                                                Screening.

•9.)                                                                Vacuuming.

•10.)                                                            Picking the right finish.

•11.)                                                            Applying the finish.

•12.)                                                            Screening between coats.

•13.)                                                            Floor care.

1.)  Safety

      The first and most important step is safety.  When doing any of the following steps I highly recommend the importance of safety and/or preventive gear such as safety goggles, ear plugs, respirators, work gloves, back brace and knee pads.  You only have one body so please take care of it!

2.)  Determine if you have hardwood.

      Do you even have hardwood that is capable of being refinished?  There are a couple ways to find this out.  If you have carpet simply tear up a couple corners in an inconspicuous place, such as a closet and peek underneath. 

        If you don’t have a finished basement ceiling you can sometimes see the flooring from there.  Sometimes you can even see the species and grade of wood from below.  It gets tricky from there if your floor is covered with tile, linoleum or another sub-floor.  If you can not see anything from the basement then you will have to tear up a small section of the sub-floor to reach the hardwood.

3.)  Remove any layers of carpet or sub-floor.

      Take a sharp razor knife and cut the carpet in three feet wide sections.  Roll up the sections and tape.  Most garbage companies won’t take carpet any wider than three feet.  Do the same with the carpet padding.  Next, grab a crowbar, hammer, nail set and snub-nosed pliers.  Pop the carpet tack strip up, being careful to pull any nails or staples all the way out.  If you don’t they could damage your sanding machine and dull your sandpaper.  Any nails that can’t be pulled need pounded down with a hammer and nail set.  Vacuum thoroughly.

Wood Sub-Floor Removal

        Grab a circular saw and set it to the proper depth of your sub-floor.  Make sure not to set it too low, as it will leave saw marks in your floor.  Cut lines across the room, then cut lines perpendicular to those, making 2′ by 2′ boxes in a grid-like fashion.  Cut as close to the walls as you can for easier removal.  Pop the 2′ by 2′ sections up.  You can buy a “Gorilla Bar” at a home improvement center if you have a lot of removal work.  Be prepared to pull a lot of nails and/or staples.

4.)  Rent the Equipment.

      Call your local rental equipment company and explain your project.  You will need a floor sander, edger and buffer.  You also need the lowest available grit sandpaper, medium (36 grit) and fine (80 grit) for the floor sander and edger.  For the buffer you need an 80 grit screen (like a drywall screen, except it’s round) and a 180 grit screen.  Make sure to get more paper than you think you will need.  The rental company should let you return any leftovers.

5.) Sanding with the Floor Sander.

      Before you start sanding you need to fill any holes caused by the nails and staples.  Buy stainable latex wood putty and fill the holes with a putty knife.  The putty should take about thirty minutes to dry. 

      Grab your lowest grit paper and put it on the big machine.  Most rental companies only carry down to 36 grit paper, but if you have any lower grit paper put that on first.  Making sure that the machine’s cord is behind you, turn the machine on and slowly let the drum handle down as you simultaneously begin walking toward the wall.  Make sure to always go with the grain of the wood.  Occasionally, in exceptional circumstances you may have to sand the floor diagonally.  This may be the only way to get the floor sanded in extreme cases.

       After the first rough cut you need to sand with a medium grit.  If you started with 36 grit then you would use 60 grit.  If you started with a grit lower than 36 your second sanding should be with 36 grit. 

      Especially pay attention to the “drum marks”.  These are lines where you put your drum down too fast and hard.  If you get one, simply run back over it with the machine a few times.

      The final cut is the fine sand.  Go up another grit of paper, 80-100 grit.  Follow the same sanding procedures as above.

6.)  Sanding with the Edger Machine.

      Sanding with the edger machine consists of using the same sandpaper as what you are using for the big machine.  When you fine sand with the edger make sure to get the previous swirl marks from your rough sandpaper out.  Don’t push down too hard on the machine, as this will leave gouge marks.  Watch when sanding around doorways so as not to leave “half-moons”.  These are just from when the machine stops and leaves half of a circle mark.

7.) Scraping.

      Now that the floor and edge sanding is completed, it’s time to scrape.  Anywhere your machine can’t reach (corners, under cabinets or radiators and stair noses) needs to be hand-scraped down to the bare wood.  You can purchase a 2″ wide scraper from any home improvement supply store.  A bastard file is used to sharpen the scraper blade.  Keep the blade as sharp as possible.  Remember to always scrape with the wood grain.  You have to scrape any old, existing finish off the floor completely so it will match your newly sanded floor.  If your are meticulous and worried about rough spots where you scraped, just take an 80 grit piece of sandpaper and lightly sand where you scraped.

8.)  Screening.

      Screening is a process used to sand and smooth out any marks or imperfections.  An 80 grit screen will work fine for the raw wood.  Try to rest the machine handles on your belly.  Don’t try to hold the machine out, away from your body.  You will lose control if you do it this way.  Try to go with the grain as much as possible.

9.)  Vacuuming

      This stage is vital in order to complete a flawless finish process.  Get a vacuum (a simple wet/dry vac will work) with a flat floor attachment.  Vac everything.  Start at the top (ceiling fans, moldings, windows door sills, heat vents and registers).  You don’t want any airborne dust floating in your finish so make sure to get everything!  Next, move to the floor.  Once again, try to go with the grain. 

      When this is completed lightly dampened a rag with mineral spirits (paint thinner) and wipe the floor clean.  This should pick up any tiny particles which would otherwise impede the integrity of the finish on your floor.  During this step I recommend you shut all windows and either take your shoes off or wear protective shoe booties.

10.)  Picking the Right Finish

      There are three choices here for the first finishing step:  a.) Stain, b.) Oil-based polyurethane or c.) Water-based polyurethane.

                  a.)  Stain

      This is used when you want to change the natural color of your floor. It can be used to diminish the visibility of water or pet stains as well.  I have always used Minwax stains and never have had a problem.  After sanding make sure to put samples down on the floor to determine the color of your liking.  Don’t go by a color guide on a sheet of paper.  Wood color fluctuates so your floor will be unique. 

      This stain takes 8-12 hours to dry, so another coat can’t be applied until the next day.  Keep in mind that the smell of this stain is strong.  In order to get rid of the smell crack windows and keep air flowing.  After staining the floor it will still need 2-3 more coats of urethane.

                  b.)  Oil-Based Polyurethane

      This is used to maintain the “natural” appearance of the floor.  It does slightly tint the wood to a light, amber, honey color.  Oil takes 8-12 hours to dry and smells very bad.  Complete curing time takes 14 days.

                  c.)  Water-Based Polyurethane

      This is used when you want the true natural color of the floor.  Wet a rag with water and wipe a small section on your raw floor.  That resultant color is the same as water-based finish.  I recommend this finish because of it’s low smell and fast drying time (2-3 hours).  Curing takes 7 days for this finish.

11.)  Applying the Finish.

a.)  Stain.

      Grab a lot of old rags without buttons or zippers.  Dip your rag in the stain and wipe in a circular motion out three feet from the wall.  When you have one section done take a clean rag and wipe the stain.  Watch for overlap marks.  You want everything to be even, not splotchy.  Continue this as you work your way out of the room.

                  b.)  Oil-Based Polyurethane

      Buy an oil-based lamb’s wool applicator.  Dip your applicator and cover the floor in a back and forth motion, up and down.  Oil finish is more forgiving of mistakes and lets you have more time.

                  c.)  Water-Based Polyurethane   

      Buy a synthetic water-based applicator pad.  Pour a basketball size puddle by the wall and work in three feet sections until you get comfortable to do more.  Just be careful not to get ahead of yourself because any finish that is left sitting will dry and “burn” the wood.  If there are bubbles in your finish this means that your applicator has too much finish in it.  Just run back over the area again.

                  12.)  Screening between Coats.

                  a.)  Stain

      Stain needs another coat of urethane before screening with 180 grit screen.  When screening a stained floor it is important to move quickly so you don’t buff any of the color off the floor.  This step just needs to knock the grain down and abrade the previous coat of urethane so that it will adhere properly.  Vac according to the instructions in step 9.).

                  b.)  Oil-Based Polyurethane

      Oil finish screening takes place after your second coat, before the last coat.  Once again use 180 grit.  Vac and coat according to instructions.

                  c.)  Water-Based Polyurethane

      This finish can be screened after the first coat with 180 screen.  It shouldn’t need screened again unless 24 hours has passed.  Vac and coat.

                  13.)  Floor Care

      Any laying water can warp and damage your hardwood floors. Wipe up any liquids.

      Grit is the hardwood floor’s number one enemy. Sweep regularly and use doormats at any entrance. Never use a vacuum with beater bars!

      Always lift furniture to avoid scratches. Do not slide! We recommend putting felt pads under all your furniture.                                                                                                                                                                               High heels can dent some hardwood floors, especially recently refinished ones.

      Never wax your hardwood floors!

      Only clean hardwood floors with approved PH neutral cleaners. Never saturate your floors with liquids when cleaning. Just lightly dampen your cleaning materials and wipe.

      Floors can be walked on and furniture may be moved back the following day after coating. We recommend not putting area rugs down for 7-14 days until the floor has completely cured.

      If you have a pet dog, it’s nails should be clipped short enough as not to cause scratches when it runs.

      Do not tape directly to the floor. There is a chance that the adhesive from the tape can pull the finish right off the floor.

GREYSTONE HOME PRODUCTS LLC ABFRWH214 FLOOR REGISTER 2″x14″ – STEEL

GREYSTONE FLOOR REGISTER Heavy steel construction Smooth operating multi- shutter damper Durable powder coated white finish Listed size is duct size unit fits 2″ x 14″

(more…)

Why Vents are Important in Improving Indoor Air Quality

It is important to have good indoor air quality. Because we are indoors a great deal — at home and at work — it is important to make sure that the indoor air we are breathing is as healthy as possible. The truth of the matter is that in some cases, the air we breathe indoors is worse than what we breathe outdoors. This is because the air inside is constantly re-circulated, and because it is in a confined space. Outdoors, the air is more dilute, and the particles not so concentrated (except in high pollution areas).

Vents are often collection places for particles that can aggravate allergies and asthma and that can cause other respiratory irritations. Not only do vents collect dust, dander, and hair of all sorts, they then release them into the air. Whether through the heating processing or by forced air conditioning, all the little particles are expelled into the air to float around and eventually be inhaled by members of the household. In order to avoid this, it is possible to use air filters. There are HEPA filters that are made from a special fabric that traps particles and prevents them from getting into the air. There are even filters that can prevent mold spores from spreading through the air and trap the particles that cause odors. These special filters can be placed in the vents, and also at the source of the blowing air in order to prevent particles from circulating through the house.

Another culprit of bad indoor air is the vacuum. So often what is vacuumed up is re-circulated in the process. Small particles are blown back into the air as one vacuums the floor. The number of particles in the air can be significantly reduced by using a vacuum specially fitted with a HEPA filter. Some vacuums also have special bags that are made from HEPA material that prevents even the smallest particles from drifting out of the bag. Multiple filters only help the vacuum more effectively trap irritating and potentially unhealthy particles.

Furniture is an ideal gathering place for all sorts of small particles. And, every time you sit down or your children or pets hop up onto the piece of furniture, the small particles are released into the air, waiting to be inhaled. You can reduce this occurrence by vacuuming your furniture using your upholstery attachment. By doing this every month or so, you can help keep the allergen in the air of your home to a minimum. And if your vacuum has a HEPA filter on it, so much the better. What you get off your furniture will not simply re-circulate through the air as you are vacuuming. Make sure you lift up any cushions and vacuum the undersides.

Keeping your respiratory system healthy can be hard work, especially if you have allergies or asthma. However, you can go a long way toward keeping the air indoors clean with the help of filters on your vents and vacuums.

Vent-Miser 91667-BR Programmable Enery Saving Vent, 10-by-6-Inches, Brown

From the Manufacturer

The Vent-Miser is an easy to install, battery operated vent with timer that can be set to shut unoccupied rooms down and force the air into other parts of the home where the warm or cool air is need. The Vent-Miser is not a thermostat, it runs independent of your heating and cooling system. Certified to save on heating and cooling bills. Customer service can be reached at 888-809-3284.

(more…)

AF410A AirFlow Breeze, Quiet Register Booster Fan, Almond Color 4″ x 10″ opening

Buy AF410A AirFlow Breeze, Quiet Register Booster Fan, Almond Color 4″ x 10″ opening at Amazon

GrillWorks Insert4″ x 12″ Maple Trimline 4″ x 12″ Wood Floor Register Vent – Trim Line Surface Insert Model Register

4″ x 12″ Wood Floor Register Vent – Trim Line Surface Insert Model RegisterOther wood species available upon request.Custom stain option requires stain brand name and finish at time of order. We may require a sample of your stain to confirm the match.Please call customer service when ordering a custom stain or if another wood species is desired.Any wood species other than Red Oak and White Oak are special order and take 3-5 days before shipping.Natural(clear coat), custom stain (more…)

Flush Mount Heating and Air Conditioning Booster Fan, Brown

Buy Flush Mount Heating and Air Conditioning Booster Fan, Brown at Amazon

Desa Int’l Heat Ground Floor Vent Kit VKG58

Includes 45 degree elbow, 7″-12″ adjustable pipe, wall firestop, horizontal square termination, and 16 screws.

(more…)

Vent-Miser 91663-BR Programmable Enery Saving Vent, 12-by-2-Inches, Brown

From the Manufacturer

The Vent-Miser is an easy to install, battery operated vent with timer that can be set to shut unoccupied rooms down and force the air into other parts of the home where the warm or cool air is need. The Vent-Miser is not a thermostat, it runs independent of your heating and cooling system. Certified to save on heating and cooling bills. Customer service can be reached at 888-809-3284.

(more…)

How to Find the Right Air Filter for your Home

Finding the right air filter for your home is important; you care about your family more than anything, so you should care about the quality of air in your home. Remember they breathe it every day, so it’s in their best interests, and yours, to choose the right filter.

Before buying an air filter, be sure to measure your vent, furnace or other filter location. It is important to measure your existing air filter exactly to the last centimeter in order to ensure you get the same size. For example, a filter that says its 16 by 25 may in reality be 15 5/8 by 24 5/8.

With this is mind, here is a breakdown of some of your best options for air filters:

The Absorber Filter

The absorber filter is directed at odor control and is primarily for homeowners who want to take advantage of filtered air and eliminate smells, especially if there are pets involved or if it’s a smoking home. If you have pets, this is probably the best kind of filter to get. It works by trapping airborne particles on the filters primary surface layer; this, combined with an active carbon filter, absorbs pet smells and other odors, like smoke.

Filter Fresh

A filter fresh is a smaller pad, usually six by six inches, that attaches to any AC or furnace filter. When you ruin your furnace or AC, the filter emits a subtle scent that lasts. There are many scent options to choose from, so take advantage of the wide variety.

Vent Filters

Vent filters use Electrostatic Register Filtration, a process that uses the vent filter’s electrostatic material to a act as a magnet for attracting dust. The vent traps cigarette smoke, odors, dust, dirt and pollen, allowing fresh air to flow through freely. It keeps microscopic particles from getting through, thus ensuring your air remains fresh. It is ideal for a home with allergies or odors and lasts as much as ninety days.

UV Eliminator Filter

The UV Eliminator Filter is a special advanced filter that traps larger particles like mold and pollen, and then uses UV light to sterilize the invading aggravators; it also eliminates surface particles. It is great for homes of all types and performs well in all environments.

Web Plus Filter

This filter is a permanent electrostatic filter that is permanently adjustable and super easy to use. It also requires little maintenance; just a wash and reinstall once a month. A solid filter, it will last a long time and create much fresher, cleaner air.

Learn more about the UV Eliminator Filter and take advantage of special introductory pricing.

« Previous Page — Next Page »